POWERLIFTER SWIVEL REWIND PET INSTALL

For the best performance, adjust to the lowest practical setting. You can turn the dial on the front of the foot to your desired floor setting.Turn the vacuum ON by pressing the red power button on the foot, then recline the machine by pressing the recline pedal.To get started, plug your machine into a properly grounded outlet.Assembling your machine is simple! Now you can start cleaning with your PowerLifter Swivel Pet vacuum!.The Pet Hair Eraser tool sits on the side of the machine.The Pet TurboEraser stores on the front of the vacuum.Put the crevice tool inside the extension wand and the wand on the back of the base From the second you start using it, you’ll notice its lightweight design and swivel steering work in your favor, giving you easy maneuverability, which makes cleaning quick and less of a chore. The tools that came with your vacuum store neatly on the unit. The BISSELL® Powerlifter Swivel Rewind Pet Vacuum gives a whole new meaning to convenient cleaning.Put the lid back on and put the Dirt Tank back on the body Lift up on the tab on the lid and take the regular foam filter out and replace with the Febreze Filter. To do so, simply press the Tank Release Button and pull the tank away from the vacuum.

POWERLIFTER SWIVEL REWIND PET INSTALL

Now is the time to install the optional Febreze Filter if you’d like.Then wrap the power cord around the upper and lower cord wrap.Slide the unconnected end of the hose into the side of the vacuum base.Wrap the hose up and around the hose wrap on the handle.Then push in and rotate clockwise until it locks into place Put the stretch hose into the body of the vacuum and align the tabs with the slot.Then, attach the tool holder to the side of the unit Next, insert the lower cord wrap and turn it clockwise to lock it in place.Using your Phillips screwdriver, secure the screws to the back of the handle There should be two screws taped to the handle in a plastic bag.First, put the Upper Handle on the base and push it down.We hope these remedies bring you suction back to your PowerLifter Pet Rewind Vacuum.Assembling your PowerLifter™ Swivel Pet vacuum is easy. Replace the bottom cover by reinserting the 6 screws using your Philips screwdriver.When the brush roll is in, turn it to align the belt.Replace the brush roll by placing the belt side of the brush in first, then turning the other end until it slides into place.Place the new belt over the motor pulley and stretch the other end over the brush roll.Inspect your belt, if it is broken or damaged it will need to be replaced.If it doesn't spin freely it is time to replace your brush roll. This video is a step-by-step guide to putting together your Powerlifter Swivel Rewind Pet vacuum.The BISSELL Powerlifter Swivel Rewind Pet Vacuum gives a w. To inspect the brush roll, set it on its end and spin it by flicking it once.Clear any debris on the brush roll or in the brush housing area and empty into a trash bin.Grab both ends of the brush and slide off the belt to remove it.Remove the 6 screws from the brush cover using your Philips screwdriver.With the machine unplugged, lay the vacuum back to expose the brush roll.Then replace the door by hooking the bottom in first and rotate it towards the machine. Replace the Post Motor Filter in the unit with the handle facing you.Gently tap the filter on the side of a trash bin to remove debris. The pleated Post Motor filter is NOT washable.Remove the filter by grasping the handle on the front of the filter and pulling out from vacuum.To access the Post Motor Filter, pull down on the latch on the front of your machine.Before replacing, make sure it is completely dry. The Pre-Motor Filters can be rinsed in warm water.

While holding the filter over a trash bin, gently separate the filter layers.

Below this, you can find the Pre-Motor Filters, Pinch the filter and lift to remove it. Powers through pet hair across the multiple surfaces in your home The BISSELL® Powerlifter Swivel Rewind Pet Vacuum gives a whole new meaning to convenient cleaning.

Remove the tank and check the suction inlet for any debris.

Check if there is a clog in the machine.

Swivel Head No Specialty Tools Multi Use Tools Flexible. Air Flow Indicator No Brush System Rotating Variable Suction Control No Power Cord Length 30 ft Automatic Cord Rewind No Hose Length 8 Filtration Filtration Multi Level Filtration Clean Filter Indicator.

Make sure the hose is secure in the foot of the suction opening. PowerLifter Pet Vacuum Model No 1309 Quantity 1 Similar Models 1309R, 1309W.

Use a broomstick handle pushing towards the elbow of the hose to clear any potential clogs.

Remove by pulling one end out of the base and turning the other end counterclockwise and out.

Start by checking your hose for any cracks or holes.

If your PowerLifter Pet Rewind vacuum has no or low suction, here are some steps to get that problem fixed.īefore you begin, you will need a Philips screwdriver.

Powerlifter swivel rewind pet